Jumping to start of image at address 0xbfca0000 U-Boot 2012.04.01 (UBNT Build Version: e200_002_80eda) (May 27 2019 - 06:34:56) Skipping PCIe port 0 BIST, in EP mode, can't tell if clocked. Skipping PCIe port 1 BIST, reset not done. (port not configured) BIST check passed. UBNT_E200 r1:0, r2:14, serial #: 24A43C0621D8 MPR 13-16777215-255 Core clock: 1000 MHz, IO clock: 600 MHz, DDR clock: 533 MHz (1066 Mhz DDR) Base DRAM address used by u-boot: 0x8f800000, size: 0x800000 DRAM: 2 GiB Clearing DRAM...... done Flash: 8 MiB Net: octeth0, octeth1, octeth2, octeth3, octeth4, octeth5, octeth6, octeth7 MMC: Octeon MMC/SD0: 0 USB: USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found Type the command 'usb start' to scan for USB storage devices. Hit any key to stop autoboot: 0 reading vmlinux.64 9724336 bytes read reading vmlinux.64.md5 argv[2]: numcores=2 argv[3]: endbootargs Allocating memory for ELF segment: addr: 0xffffffff81100000 (adjusted to: 0x1100000), size 0x199ccc0 ## Loading big-endian Linux kernel with entry point: 0xffffffff81794b60 ... Bootloader: Done loading app on coremask: 0x3 Starting cores 0x3 [ 0.000000] Linux version 5.4.179 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16495-bf0c965af0))2 [ 0.000000] Skipping L2 locking due to reduced L2 cache size [ 0.000000] CVMSEG size: 0 cache lines (0 bytes) [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 000d9301 (Cavium Octeon II) [ 0.000000] Checking for the multiply/shift bug... no. [ 0.000000] Checking for the daddiu bug... no. [ 0.000000] Wasting 278528 bytes for tracking 4352 unused pages [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Using passed Device Tree. [ 0.000000] software IO TLB: mapped [mem 0x02b0b000-0x02b4b000] (0MB) [ 0.000000] Primary instruction cache 37kB, virtually tagged, 37 way, 8 sets, linesize 128 bytes. [ 0.000000] Primary data cache 32kB, 32-way, 8 sets, linesize 128 bytes. [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000001100000-0x00000000efffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000001100000-0x0000000002a9bfff] [ 0.000000] node 0: [mem 0x0000000002b00000-0x000000000eefffff] [ 0.000000] node 0: [mem 0x000000000f200000-0x000000000fdfffff] [ 0.000000] node 0: [mem 0x0000000020000000-0x000000008f7fffff] [ 0.000000] Zeroed struct page in unavailable ranges: 7780 pages [ 0.000000] Initmem setup node 0 [mem 0x0000000001100000-0x000000008f7fffff] [ 0.000000] percpu: Embedded 18 pages/cpu s35872 r8192 d29664 u73728 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 508437 [ 0.000000] Kernel command line: mtdparts=phys_mapped_flash:640k(boot0)ro,640k(boot1)ro,64k(eeprom)ro root=/dev0 [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 2003496K/2066032K available (6766K kernel code, 378K rwdata, 1048K rodata, 1332K init, 1669) [ 0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 127 [ 0.000000] random: get_random_bytes called from 0xffffffff81903a20 with crng_init=0 [ 4.080574] clocksource: OCTEON_CVMCOUNT: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 8815s [ 4.099236] Calibrating delay loop (skipped) preset value.. 2000.00 BogoMIPS (lpj=4000000) [ 4.107472] pid_max: default: 32768 minimum: 301 [ 4.112165] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 4.119465] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 4.127843] Checking for the daddi bug... no. [ 4.132599] rcu: Hierarchical SRCU implementation. [ 4.137446] smp: Bringing up secondary CPUs ... [ 4.142118] SMP: Booting CPU01 (CoreId 1)... [ 4.146372] CPU1 revision is: 000d9301 (Cavium Octeon II) [ 4.146468] smp: Brought up 1 node, 2 CPUs [ 4.157895] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 4.167498] futex hash table entries: 512 (order: 4, 65536 bytes, linear) [ 4.174681] NET: Registered protocol family 16 [ 4.183677] PCIe: Port 0 in endpoint mode, skipping. [ 4.188497] PCIe: Initializing port 1 [ 4.203129] PCIe: Port 1 stuck in reset, skipping. [ 4.216225] SCSI subsystem initialized [ 4.220001] usbcore: registered new interface driver usbfs [ 4.225372] usbcore: registered new interface driver hub [ 4.230669] usbcore: registered new device driver usb [ 4.235693] EDAC MC: Ver: 3.0.0 [ 4.239518] PCI host bridge to bus 0000:00 [ 4.243476] pci_bus 0000:00: root bus resource [mem 0x1000000000000] [ 4.249804] pci_bus 0000:00: root bus resource [io 0x0000] [ 4.255365] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 4.262145] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 4.270634] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 4.277709] clocksource: Switched to clocksource OCTEON_CVMCOUNT [ 4.284046] thermal_sys: Registered thermal governor 'step_wise' [ 4.284189] NET: Registered protocol family 2 [ 4.294505] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 4.302988] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 4.311405] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 4.319439] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear) [ 4.326823] TCP: Hash tables configured (established 16384 bind 16384) [ 4.333266] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 4.339938] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 4.347179] NET: Registered protocol family 1 [ 4.351401] PCI: CLS 0 bytes, default 128 [ 4.356340] workingset: timestamp_bits=46 max_order=19 bucket_order=0 [ 4.369240] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 4.375069] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 4.384656] random: fast init done [ 4.389381] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 4.397345] octeon_gpio 1070000000800.gpio-controller: OCTEON GPIO driver probed. [ 4.404898] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 4.412358] printk: console [ttyS0] disabled [ 4.416512] 1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 34, base_baud = 37500000) is a OCTEON [ 4.426316] printk: console [ttyS0] enabled [ 4.426316] printk: console [ttyS0] enabled [ 4.434650] printk: bootconsole [early0] disabled [ 4.434650] printk: bootconsole [early0] disabled [ 4.444261] 1180000000c00.serial: ttyS1 at MMIO 0x1180000000c00 (irq = 35, base_baud = 37500000) is a OCTEON [ 4.454363] octeon_rng octeon_rng: Octeon Random Number Generator [ 4.463401] loop: module loaded [ 4.466580] Loading iSCSI transport class v2.0-870. [ 4.472152] physmap-flash 1f400000.nor: Can't get bank width from device tree [ 4.479339] physmap-flash: probe of 1f400000.nor failed with error -22 [ 4.486193] spi-octeon 1070000001000.spi: OCTEON SPI bus driver [ 4.494010] mdio_octeon 1180000001800.mdio: Probed [ 4.499448] mdio_octeon 1180000001900.mdio: Probed [ 4.504765] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.511321] ehci-pci: EHCI PCI platform driver [ 4.515820] ehci-platform: EHCI generic platform driver [ 4.521185] ehci-platform 16f0000000000.ehci: EHCI Host Controller [ 4.527407] ehci-platform 16f0000000000.ehci: new USB bus registered, assigned bus number 1 [ 4.535851] ehci-platform 16f0000000000.ehci: irq 56, io mem 0x16f0000000000 [ 4.557716] ehci-platform 16f0000000000.ehci: USB 2.0 started, EHCI 1.00 [ 4.564832] hub 1-0:1.0: USB hub found [ 4.568632] hub 1-0:1.0: 2 ports detected [ 4.572942] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.579165] ohci-platform: OHCI generic platform driver [ 4.584516] ohci-platform 16f0000000400.ohci: Generic Platform OHCI controller [ 4.591779] ohci-platform 16f0000000400.ohci: new USB bus registered, assigned bus number 2 [ 4.600202] ohci-platform 16f0000000400.ohci: irq 56, io mem 0x16f0000000400 [ 4.670058] hub 2-0:1.0: USB hub found [ 4.673854] hub 2-0:1.0: 2 ports detected [ 4.678237] usbcore: registered new interface driver usb-storage [ 4.684397] i2c-octeon 1180000001000.i2c: probed [ 4.689162] i2c-octeon 1180000001200.i2c: probed [ 4.693911] octeon_wdt: Initial granularity 5 Sec [ 4.698971] EDAC DEVICE0: Giving out device to module octeon-cpu controller cache: DEV octeon_pc_edac (INTERRUP) [ 4.709365] EDAC DEVICE1: Giving out device to module octeon-l2c controller octeon_l2c_err: DEV octeon_l2c_edac) [ 4.720328] octeon_lmc_edac octeon_lmc_edac.0: Disabled (ECC not enabled) [ 4.754258] Interface 0 has 4 ports (SGMII) [ 4.758498] Interface 1 has 4 ports (SGMII) [ 4.766336] NET: Registered protocol family 10 [ 4.772237] Segment Routing with IPv6 [ 4.775987] NET: Registered protocol family 17 [ 4.780486] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to lo. [ 4.793605] 8021q: 802.1Q VLAN Support v1.8 [ 4.797983] Bootbus flash: Setting flash for 8MB flash at 0x1f400000 [ 6.471520] phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0009 [ 6.481908] Amd/Fujitsu Extended Query Table at 0x0040 [ 6.487081] Amd/Fujitsu Extended Query version 1.1. [ 6.492153] phys_mapped_flash: Swapping erase regions for top-boot CFI table. [ 6.499309] number of CFI chips: 1 [ 6.502739] 3 cmdlinepart partitions found on MTD device phys_mapped_flash [ 6.509635] Creating 3 MTD partitions on "phys_mapped_flash": [ 6.515402] 0x000000000000-0x0000000a0000 : "boot0" [ 6.520818] 0x0000000a0000-0x000000140000 : "boot1" [ 6.526179] 0x000000140000-0x000000150000 : "eeprom" [ 6.532021] OF: fdt: not creating '/sys/firmware/fdt': CRC check failed [ 6.538857] Waiting for root device /dev/mmcblk0p2... [ 13.217720] crng init done [ 14.253517] mmc0: new DDR MMC card at address 0001 [ 14.258664] mmcblk0: mmc0:0001 SEM04G 3.69 GiB [ 14.263342] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 14.269414] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 14.275415] mmcblk0rpmb: mmc0:0001 SEM04G partition 3 2.00 MiB, chardev (251:0) [ 14.283422] mmcblk0: p1 p2 [ 14.292209] VFS: Mounted root (squashfs filesystem) readonly on device 179:2. [ 14.299813] Freeing unused kernel memory: 1332K [ 14.304383] This architecture does not have kernel memory protection. [ 14.310839] Run /sbin/init as init process [ 14.468395] SQUASHFS error: xz decompression failed, data probably corrupt [ 14.475296] SQUASHFS error: squashfs_read_data failed to read block 0x94d8a [ 14.498128] SQUASHFS error: xz decompression failed, data probably corrupt [ 14.505020] SQUASHFS error: squashfs_read_data failed to read block 0x94d8a [ 14.527841] SQUASHFS error: xz decompression failed, data probably corrupt [ 14.534735] SQUASHFS error: squashfs_read_data failed to read block 0x94d8a [ 14.541741] Starting init: /sbin/init exists but couldn't execute it (error -14) [ 14.549156] Run /etc/init as init process [ 14.554708] Run /bin/init as init process [ 14.558790] Run /bin/sh as init process [ 14.562770] Starting init: /bin/sh exists but couldn't execute it (error -14) [ 14.569930] Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux D. [ 14.584125] Rebooting in 1 seconds..